INSTALLATION NOTES for OpenBSD/luna88k 3.8 What is OpenBSD? ---------------- OpenBSD is a fully functional, multi-platform UN*X-like Operating System based on Berkeley Networking Release 2 (Net/2) and 4.4BSD-Lite. There are several operating systems in this family, but OpenBSD differentiates itself by putting security and correctness first. The OpenBSD team strives to achieve what is called a 'secure by default' status. This means that an OpenBSD user should feel safe that their newly installed machine will not be compromised. This 'secure by default' goal is achieved by taking a proactive stance on security. Since security flaws are essentially mistakes in design or implement- ation, the OpenBSD team puts as much importance on finding and fixing existing design flaws and implementation bugs as it does writing new code. This means that an OpenBSD system will not only be more secure, but it will be more stable. The source code for all critical system components has been checked for remote-access, local-access, denial- of-service, data destruction, and information-gathering problems. In addition to bug fixing, OpenBSD has integrated strong cryptography into the base system. A fully functional IPsec implementation is provided as well as support for common protocols such as SSL and SSH. Network filtering and monitoring tools such as packet filtering, NAT, and bridging are also standard, as well as several routing services, such as BGP and OSPF. For high performance demands, support for hardware cryptography has also been added to the base system. Because security is often seen as a tradeoff with usability, OpenBSD provides as many security options as possible to allow the user to enjoy secure computing without feeling burdened by it. To integrate more smoothly in other environments, OpenBSD 3.8 also provides, on some platforms, several binary emulation subsystems (which includes iBCS2, Linux, OSF/1, SunOS, SVR4, Solaris, and Ultrix compatibility), aiming at making the emulation as accurate as possible so that it is transparent to the user. Because OpenBSD is from Canada, the export of Cryptography pieces (such as OpenSSH, IPsec, and Kerberos) to the world is not restricted. (NOTE: OpenBSD can not be re-exported from the US once it has entered the US. Because of this, take care NOT to get the distribution from an FTP server in the US if you are outside of Canada and the US.) A comprehensive list of the improvements brought by the 3.8 release is available on the web at http://www.OpenBSD.org/38.html. OpenBSD/luna88k runs on the OMRON Luna-88K family of workstations. Sources of OpenBSD: ------------------- This is a list of currently known FTP servers at the time of the 3.8 release. For a more recent list, please refer to http://www.OpenBSD.org/ftp.html Main server in Canada: ftp://ftp.OpenBSD.org/pub/OpenBSD (Alberta) Argentina: ftp://ftp.openbsd.md5.com.ar/pub/OpenBSD (Buenos Aires) Australia: ftp://mirror.aarnet.edu.au/pub/OpenBSD (Canberra, .au only) ftp://ftp.it.net.au/mirrors/OpenBSD (Perth) ftp://ftp.planetmirror.com/pub/OpenBSD (Sydney) ftp://mirror.pacific.net.au/OpenBSD (Sydney) ftp://openbsd.wiretapped.net/pub/OpenBSD (Sydney) Austria: ftp://gd.tuwien.ac.at/opsys/OpenBSD (Vienna) ftp://playboy.wu-wien.ac.at/pub/OpenBSD (Vienna) Belgium: ftp://ftp.scarlet.be/pub/openbsd ftp://ftp.belnet.be/packages/openbsd (Brussels) ftp://openbsd.rug.ac.be/pub/OpenBSD (Ghent) Brazil: ftp://ftp.openbsd.org.br/pub/OpenBSD (Curitiba) ftp://ftp.das.ufsc.br/pub/OpenBSD (Santa Catarina) Bulgaria: ftp://ftp.bg.openbsd.org/pub/OpenBSD (Plovdiv) Canada: ftp://ftp.ca.openbsd.org/pub/OpenBSD (Edmonton) China: ftp://ftp.shellhung.org/pub/OpenBSD (Hong Kong) Czech Republic: ftp://ftp.openbsd.cz/pub/OpenBSD (Prague) Denmark: ftp://mirrors.dotsrc.org/openbsd (Aalborg) Finland: ftp://ftp.fi.debian.org/pub/OpenBSD ftp://ftp.jyu.fi/pub/OpenBSD (Jyvaskyla) France: ftp://ftp.ac-creteil.fr/OpenBSD ftp://ftp.bsdfr.org/pub/OpenBSD (Paris) ftp://ftp.club-internet.fr/pub/OpenBSD (Paris) ftp://ftp.fr.openbsd.org/pub/OpenBSD (Paris) Germany: ftp://ftp.de.openbsd.org/unix/OpenBSD (Berlin) ftp://ftp.tu-clausthal.de/pub/OpenBSD (Clausthal) ftp://ftp.freenet.de/pub/ftp.openbsd.org/pub/OpenBSD (Duesseldorf) ftp://openbsd.informatik.uni-erlangen.de/pub/OpenBSD (Erlangen) ftp://ftp-stud.fht-esslingen.de/pub/OpenBSD (Esslingen) ftp://pandemonium.tiscali.de/pub/OpenBSD (Frankfurt) ftp://openbsd.bay13.net/pub/OpenBSD (Hamburg) ftp://ftp.leo.org/pub/OpenBSD (Muenchen) ftp://ftp.uni-stuttgart.de/pub/OpenBSD (Stuttgart) ftp://ftp.fh-wolfenbuettel.de/pub/os/openbsd (Wolfenbuettel) Greece: ftp://filoktitis.noc.uoa.gr/pub/OpenBSD (Athens) ftp://ftp.physics.auth.gr/pub/mirrors/OpenBSD/OpenBSD (Thessaloniki) ftp://ftp.duth.gr/pub/OpenBSD (Thrace) Hungary: ftp://ftp.fsn.hu/pub/OpenBSD Ireland: ftp://ftp.esat.net/pub/OpenBSD (Dublin) Italy: ftp://ftp.openbsd.it/pub/Unix/OpenBSD (Napoli) ftp://na.mirror.garr.it/mirrors/OpenBSD (Napoli) Japan: ftp://ftp.netlab.is.tsukuba.ac.jp/pub/os/OpenBSD (Ibaraki) ftp://ftp.iij.ad.jp/pub/OpenBSD (Tokyo) ftp://ftp.jp.openbsd.org/pub/OpenBSD (Tokyo) ftp://ftp.kddlabs.co.jp/OpenBSD (Tokyo) Latvia: ftp://ftp.bsd.lv/pub/OpenBSD Lithuania: ftp://ftp.openbsd.lt/pub/OpenBSD The Netherlands: ftp://ftp.nl.uu.net/pub/OpenBSD (Amsterdam) ftp://ftp.calyx.nl/pub/OpenBSD (Amsterdam) ftp://ftp.nluug.nl/pub/OpenBSD (Utrecht) Norway: ftp://ftp.inet.no/pub/OpenBSD (Oslo) ftp://ftp.uninett.no/pub/OpenBSD (Oslo) Poland: ftp://sunsite.icm.edu.pl/pub/OpenBSD ftp://ftp.man.szczecin.pl/pub/BSD/OpenBSD Portugal: ftp://ftp.fmed.uc.pt/pub/OpenBSD Romania: ftp://ftp.physics.uvt.ro/pub/OpenBSD (Timisoara) Russia: ftp://ftp.chg.ru/pub/OpenBSD (Chernogolovka-Moscow) ftp://ftp.gamma.ru/pub/OpenBSD (Moscow) ftp://ftp.radio-msu.net/pub/OpenBSD (Moscow) Saudi Arabia: ftp://ftp.isu.net.sa/pub/mirrors/ftp.openbsd.org/pub/OpenBSD Spain: ftp://ftp.rediris.es/mirror/OpenBSD (Madrid) Sweden: ftp://ftp.stacken.kth.se/pub/OpenBSD (Stockholm) ftp://ftp.sunet.se/pub/OpenBSD (Uppsala) Switzerland: ftp://ftp.solnet.ch/mirror/OpenBSD ftp://ftp.dragonbsd.swiss-anime.ch/pub/OpenBSD (Bern) ftp://sunsite.cnlab-switch.ch/pub/OpenBSD (Zurich) Taiwan: ftp://ftp2.openbsd.org.tw/pub/OpenBSD ftp://openbsd.nsysu.edu.tw/pub/BSD/OpenBSD ftp://ftp.twaren.net/BSD/OpenBSD Turkey: ftp://ftp.linux.org.tr/pub/OpenBSD Ukraine: ftp://ftp.openbsd.org.ua/pub/OpenBSD (Kiev) United Kingdom: ftp://ftp.plig.org/pub/OpenBSD (London) USA: ftp://ftp5.usa.openbsd.org/pub/OpenBSD (Redwood City, CA) ftp://ftp3.usa.openbsd.org/pub/OpenBSD (Boulder, CO) ftp.lug.udel.edu/pub/OpenBSD (Newark, DE) ftp://reflection.ncsa.uiuc.edu/pub/OpenBSD (Champaign, IL) ftp://mirror.sg.depaul.edu/pub/OpenBSD (Chicago, IL) ftp://rt.fm/pub/OpenBSD (Lake in the Hills, IL) ftp://ftp.groupbsd.org/pub/OpenBSD (Hillsborough, NC) ftp://ftp.cse.buffalo.edu/pub/OpenBSD (Buffalo, NY) ftp://ftp.crimelabs.net/pub/OpenBSD (New York, NY) ftp://openbsd.mirrors.pair.com (Pittsburgh, PA) ftp://carroll.cac.psu.edu/pub/OpenBSD (State College, PA) ftp://mirrors.rcn.net/pub/OpenBSD (Fairfax, VA) ftp://openbsd.secsup.org/pub/openbsd (Fairfax, VA) ftp://ftp.tux.org/bsd/openbsd (Springfield, VA) ftp://mirror.cs.wisc.edu/pub/mirrors/OpenBSD (Madison, WI) Additionally, the file ftp://ftp.OpenBSD.org/pub/OpenBSD/ftplist contains a list which is continually updated. If you wish to become a distribution site for OpenBSD, contact . OpenBSD 3.8 Release Contents: ----------------------------- The OpenBSD 3.8 release is organized in the following way. In the .../3.8 directory, for each of the architectures having an OpenBSD 3.8 binary distribution, there is a sub-directory. The luna88k-specific portion of the OpenBSD 3.8 release is found in the "luna88k" subdirectory of the distribution. That subdirectory is laid out as follows: .../3.8/luna88k/ INSTALL.luna88k Installation notes; this file. CKSUM, MD5 Output of the cksum(1) and md5(1) programs, usable for verification of the correctness of downloaded files. *.tgz luna88k binary distribution sets; see below. bsd A stock GENERIC luna88k kernel which will be installed on your system during the install. bsd.rd A compressed RAMDISK kernel; the embedded filesystem contains the installation tools. Used for simple installation from a pre-existing system. These files can be used to make a bootable tape suitable for installation. They can also be used to configure an NFS server to support installation over the network. See the section "Getting the OpenBSD system onto Useful Media" for more information. The OpenBSD/luna88k binary distribution sets contain the binaries which comprise the OpenBSD 3.8 release for luna88k systems. There are ten binary distribution sets. The binary distribution sets can be found in the "luna88k" subdirectory of the OpenBSD 3.8 distribution tree, and are as follows: base38 The OpenBSD/luna88k 3.8 base binary distribution. You MUST install this distribution set. It contains the base OpenBSD utilities that are necessary for the system to run and be minimally functional. It excludes everything described below. [ 79.1 MB gzipped, 188.3 MB uncompressed ] comp38 The OpenBSD/luna88k Compiler tools. All of the tools relating to C, C++, and fortran are supported. This set includes the system include files (/usr/include), the linker, the compiler tool chain, and the various system libraries. This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. [ 17.2 MB gzipped, 50.0 MB uncompressed ] etc38 This distribution set contains the system configuration files that reside in /etc and in several other places. This set MUST be installed if you are installing the system from scratch, but should NOT be used if you are upgrading. (If you are upgrading, it's recommended that you get a copy of this set and CAREFULLY upgrade your configuration files by hand; see the section named "Upgrading a previously-installed OpenBSD System" below.) [ 1.6 MB gzipped, 6.3 MB uncompressed ] game38 This set includes the games and their manual pages. [ 6.8 MB gzipped, 14.4 MB uncompressed ] man38 This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. [ 6.4 MB gzipped, 22.9 MB uncompressed ] misc38 This set includes the system dictionaries (which are rather large), and the typesettable document set. [ 2.1 MB gzipped, 7.1 MB uncompressed ] xbase38 This set includes the base X distribution. This includes programs, headers and libraries. [ 84.6 MB gzipped, 165.1 MB uncompressed ] xetc38 This set includes the X window system configuration files that reside in /etc. It's the equivalent of etc38 for X. [ 0.9 MB gzipped, 2.0 MB uncompressed ] xfont38 This set includes all of the X fonts. [ 31.6 MB gzipped, 35.3 MB uncompressed ] xshare38 This set includes all text files equivalent between all architectures. [ 1.9 MB gzipped, 10.2 MB uncompressed ] OpenBSD System Requirements and Supported Devices: -------------------------------------------------- OpenBSD/luna88k 3.8 runs on the OMRON Luna-88K workstations family. The minimal configuration requires 16MB of RAM and ~250MB of disk space. To install the entire system requires much more disk space, and to compile the system, more RAM is recommended. Supported devices: On-board console serial port (siotty) On-board LANCE Ethernet interface (le) On-board SCSI controllers (spc) LCD display on front panel (not user-controllable) Keyboard, mouse and frame buffer (suitable as a console too) Devices not listed above are not supported by this release. Getting the OpenBSD System onto Useful Media: --------------------------------------------- Installation is supported from several media types, including: CD-ROM FFS partitions (for upgrades only) Tape Remote NFS partitions FTP HTTP The steps necessary to prepare the distribution sets for installation depend on which method of installation you choose. Some methods require a bit of setup first that is explained below. The installation allows installing OpenBSD directly from FTP mirror sites over the internet, however you must consider the speed and reliability of your internet connection for this option. It may save much time and frustration to use ftp get/reget to transfer the distribution sets to a local server or disk and perform the installation from there, rather than directly from the internet. The variety of options listed may seem confusing, but situations vary widely in terms of what peripherals and what sort of network arrangements a user has, the intent is to provide some way that will be practical. Creating an (optionally bootable) installation tape: To install OpenBSD from a tape, you need to make a tape that contains the distribution set files, each in "tar" format or in "gzipped tar format". First you will need to transfer the distribution sets to your local system, using ftp or by mounting the CD-ROM containing the release. Then you need to make a tape containing the files. If you're making the tape on a UN*X-like system, the easiest way to do so is make a shell script along the following lines, call it "/tmp/maketape". #! /bin/sh TAPE=${TAPE:-/dev/nrst0} mt -f ${TAPE} rewind if test $# -lt 1 then dd of=${TAPE} if=bsd.rd obs=8k conv=sync fi for file in base etc comp game man misc xbase xetc xfont xshare do dd if=${file}38.tgz of=${TAPE} obs=8k conv=sync done tar cf ${TAPE} bsd mt -f ${TAPE} offline # end of script And then: cd .../3.8/luna88k sh -x /tmp/maketape Note that, by default, this script creates a bootable tape. If you only want to fetch the OpenBSD files from tape, but want to boot from another device, you can save time and space creating the tape this way: cd .../3.8/luna88k sh -x /tmp/maketape noboot If you're using a system other than OpenBSD or SunOS, the tape name and other requirements may change. You can override the default device name (/dev/nrst0) with the TAPE environment variable. For example, under Solaris, you would probably run: TAPE=/dev/rmt/0n sh -x /tmp/maketape Note that, when installing, the tape can be write-protected (i.e. read-only). To install OpenBSD using a remote partition, mounted via NFS, you must do the following: NOTE: This method of installation is recommended only for those already familiar with using BSD network configuration and management commands. If you aren't, this documentation should help, but is not intended to be all-encompassing. Place the OpenBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading OpenBSD. This will probably require modifying the /etc/exports file of the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privileges on the server.) You need to know the numeric IP address of the NFS server, and, if the server is not on a network directly connected to the machine on which you're installing or upgrading OpenBSD, you need to know the numeric IP address of the router closest to the OpenBSD machine. Finally, you need to know the numeric IP address of the OpenBSD machine itself. Once the NFS server is set up properly and you have the information mentioned above, you can proceed to the next step in the installation or upgrade process. If you are upgrading OpenBSD, you also have the option of installing OpenBSD by putting the new distribution sets somewhere in your existing file system, and using them from there. To do that, do the following: Place the distribution sets you wish to upgrade somewhere in your current file system tree. At a bare minimum, you must upgrade the "base" binary distribution, and so must put the "base38" set somewhere in your file system. It is recommended that you upgrade the other sets, as well. Preparing your System for OpenBSD Installation: ----------------------------------------------- Luna-88K do not require any specific preparation prior to the OpenBSD installation. However, you might want to get familiar with the PROM interface, in order to be able to boot the installation media and, later, specify the correct boot parameters. The first set of DIP switches in the front panel (DIP SW1) is used to select the machine behaviour upon powerup, as well as the preferred console device. The meaning of these switches will depend upon your particular machine. On the Luna-88k, the 'down' position is 'on', and the 'up' position is 'off', while the Luna-88k2 uses the opposite convention (i.e. 'up' is 'on' and 'down' is 'off'). If the leftmost switch in SW1, #1, is in the 'off' position, the system will auto-boot from the boot device saved in NVRAM. Otherwise, the boot process will stop at the PROM prompt. The second switch in SW1, #2, selects the console device. When in the 'on' position, it selects the serial console port as the console; otherwise, the graphics display and keyboard are used as the console. While the Luna-88K2 uses ``standard'' serial ports, the earlier Luna-88K have a specific connector. Wiring information for this connector can be found at the following URL: http://www.kk.iij4u.or.jp/~taokamur/luna68k/serial.jpg Installing the OpenBSD System: ------------------------------ Installing OpenBSD is a relatively complex process, but if you have this document in hand and are careful to read and remember the information which is presented to you by the install program, it shouldn't be too much trouble. Before you begin, you should know the geometry of your hard disk, i.e. the sector size (note that sector sizes other than 512 bytes are not currently supported), the number of sectors per track, the number of tracks per cylinder (also known as the number of heads), and the number of cylinders on the disk. The OpenBSD kernel will try to discover these parameters on its own, and if it can it will print them at boot time. If possible, you should use the parameters it prints. (You might not be able to because you're sharing your disk with another operating system, or because your disk is old enough that the kernel can't figure out its geometry.) There are several ways to install OpenBSD onto a disk. The easiest way in terms of preliminary setup is to use the OpenBSD ramdisk kernel, bsd.rd, which can be booted from tape, or an existing Mach partition. Booting from the Installation Media: Prior to attempting an installation, everything of value on the target system should be backed up. While installing OpenBSD does not necessarily wipe out all the partitions on the hard disk, errors during the install process can have unforeseen consequences and will probably leave the system unbootable if the installation process is not completed. Availability of the installation media for the prior installation, such as a Luna-88K Mach tape, is always a good insurance, should it be necessary to "go back" for some reason. After taking care of all that, the system should be brought down gracefully using the shutdown(8) and/or halt(8) commands, which will eventually go back to the PROM prompt. Remember that the leftmost switch from the front panel DIP switch #1 must be down to access the PROM prompt. Booting from an installation tape: The internal tape drive is usually configured as SCSI ID #4. At the prompt, enter b st(0,0,0) to boot the first file from the tape. If your tape drive uses a different SCSI ID, replace the middle number with the appropriate number from the following table: tape drive SCSI ID: 0 1 2 3 4 5 6 middle number for st(): 4 3 2 1 0 6 5 If the tape drive is connected to the external SCSI controller, add 10 to the middle number. For example, to boot from a tape drive with ID #5 connected to the external controller, enter: b st(0,16,0) Booting from an existing partition: At the prompt, enter b sd(0,n,p) bsd.rd to boot bsd.rd from the specified disk and partition. Replace 'p' with the partition number (usually 0, for the 'a' partition), and 'n' with the appropriate number from the following table: disk drive SCSI ID: 0 1 2 3 4 5 6 value of 'n': 6 5 4 3 2 1 0 If the disk drive is connected to the external SCSI controller, add 10 to this number. For example, to boot from a disk drive with ID #0 connected to the external controller, enter: b sd(0,16,0) bsd.rd Installing the system: You should now be ready to install OpenBSD. The following is a walk-through of the steps you will take while getting OpenBSD installed on your hard disk. If any question has a default answer, it will be displayed in brackets ("[]") after the question. If you wish to stop the installation, you may hit Control-C at any time, but if you do, you'll have to begin the installation process again from scratch. Using Control-Z to suspend the process may be a better option, or at any prompt enter '!' to get a shell, from which 'exit' will return you back to that prompt (no refresh of the prompt though). Boot your machine from the installation media as described above. It will take a while to load the kernel especially from a slow network connection, most likely more than a minute. If some action doesn't eventually happen, or the spinning cursor has stopped and nothing further has happened, either your boot media is bad, your diskless setup isn't correct, or you may have a hardware or configuration problem. Once the kernel has loaded, you will be presented with the OpenBSD kernel boot messages. You will want to read them to determine your disk's name and geometry. Its name will be something like "sd0" or "wd0" and the geometry will be printed on a line that begins with its name. As mentioned above, you will need your disk's geometry when creating OpenBSD partitions. You will also need to know the device name to tell the install tools what disk to install on. If you cannot read the messages as they scroll by, do not worry -- you can get at this information later inside the install program. You will next be asked for your terminal type. You should choose the terminal type from amongst those listed. (If your terminal type is xterm, just use vt100). After entering the terminal type you will be asked whether you wish to do an "(I)nstall" or an "(U)pgrade". Enter 'I' for a fresh install or 'U' to upgrade an existing installation. You will be presented with a welcome message and asked if you really wish to install (or upgrade). Assuming you answered yes, the install program will then tell you which disks of that type it can install on, and ask you which it should use. The name of the disk is typically "sd0" for SCSI drives. Reply with the name of your disk. Next the disk label which defines the layout of the OpenBSD file systems must be set up. The installation script will invoke an interactive editor allowing you to do this. Note that partition 'c' inside this disk label should ALWAYS reflect the entire disk, including any non-OpenBSD portions. If you are labeling a new disk, you will probably start out with an 'a' partition that spans the disk. In this case you should delete 'a' before adding new partitions. The root file system should be in partition 'a', and swap is usually in partition 'b'. It is recommended that you create separate partitions for /usr, /tmp, and /var, and if you have room for it, one for /home. In doing this, remember to skip 'c', leaving it as type "unused". For help in the disk label editor, enter '?' or 'M' to view the manual page (see the info on the ``-E'' flag). The swap partition (usually 'b') should have a type of "swap", all other native OpenBSD partitions should have a type of "4.2BSD". Block and fragment sizes are usually 8192 and 1024 bytes, but can also be 4096 and 512 or even 16384 and 2048 bytes. The install program will now label your disk and ask which file systems should be created on which partitions. It will auto- matically select the 'a' partition to be the root file system. Next it will ask for which disk and partition you want a file system created on. This will be the same as the disk name (e.g. "sd0") with the letter identifying the partition (e.g. "d") appended (e.g. "sd0d"). Then it will ask where this partition is to be mounted, e.g. /usr. This process will be repeated until you enter "done". At this point you will be asked to confirm that the file system information you have entered is correct, and given an opportunity to change the file system table. Next it will create the new file systems as specified, OVERWRITING ANY EXISTING DATA. This is the point of no return. After all your file systems have been created, the install program will give you an opportunity to configure the network. The network configuration you enter (if any) can then be used to do the install from another system using HTTP or FTP, and will also be the configuration used by the system after the installation is complete. If you select to configure the network, the install program will ask you for the name of your system and the DNS domain name to use. Note that the host name should be without the domain part, and that the domain name should NOT include the host name part. Next the system will give you a list of network interfaces you can configure. For each network interface you select to configure, it will ask for the IP address to use, the symbolic host name to use, the netmask to use, and any interface-specific flags to set. The interface-specific flags are usually used to determine which media the network card is to use. Typically no media flags are required as autodetection normally works, but you will be prompted with a list of the acceptable media flags, and asked if you want to provide any. In doubt, do not enter any media flags; or you can refer to the manual page for your interface for the appropriate flags. After all network interfaces have been configured, the install pro- gram will ask for a default route and IP address of the primary name server to use. You will also be presented with an opportunity to edit the host table. At this point you will be allowed to edit the file system table that will be used for the remainder of the installation and that will be used by the finished system, following which the new file systems will be mounted to complete the installation. After these preparatory steps have been completed, you will be able to extract the distribution sets onto your system. There are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS, or a local disk partition. To install via FTP: To begin an FTP install you will need the following pieces of information. Don't be daunted by this list; the defaults are sufficient for most people. 1) Proxy server URL if you are using a URL-based FTP proxy (squid, CERN FTP, Apache 1.2 or higher). You need to define a proxy if you are behind a firewall that blocks outgoing FTP (assuming you have a proxy available to use). 2) Do you need to use active mode FTP? By default, ftp will attempt to use passive mode and fall back to an active connection if the server does not support passive mode. You only need to enable this option if you are connecting to a buggy FTP daemon that implements passive FTP incorrectly. Note that you will not be asked about active FTP if you are using a proxy. 3) The IP address (or hostname if you enabled DNS earlier in the install) of an FTP server carrying the OpenBSD 3.8 distribution. If you don't know, just hit return when asked if you want to see a list of such hosts. 4) The FTP directory holding the distribution sets. The default value of pub/OpenBSD/3.8/luna88k is almost always correct. 5) The login and password for the FTP account. You will only be asked for a password for non-anonymous FTP. For instructions on how to complete the installation via FTP, see the section named "Common URL installations" below. To install via HTTP: To begin an HTTP install you will need the following pieces of information: 1) Proxy server URL if you are using a URL-based HTTP proxy (squid, CERN FTP, Apache 1.2 or higher). You need to define a proxy if you are behind a firewall that blocks outgoing HTTP connections (assuming you have a proxy available to use). 2) The IP address (or hostname if you enabled DNS earlier in the install) of an HTTP server carrying the OpenBSD 3.8 distribution. If you don't know, just hit return when asked if you want to see a list of such hosts. 3) The directory holding the distribution sets. There is no standard location for this; You should use the directory specified along with the server in the list of official HTTP mirror sites that you received in step 3. For instructions on how to complete the installation via HTTP, see the section named "Common URL installations" below. To install from tape: In order to install from tape, the distribution sets to be installed must have been written to tape previously, either in tar format or gzip-compressed tar format. You will also have to identify the tape device where the distribution sets are to be extracted from. This will typically be "nrst0" (no-rewind, raw interface). Next you will have to specify how many files have to be skipped on the tape. This number is usually zero, unless you have created a bootable tape, in which case the number will be 1. The install program will not automatically detect whether an image has been compressed, so it will ask for that information before starting the extraction. To install from CD-ROM: When installing from a CD-ROM, you will be asked which device holds the distribution sets. This will typically be "cd0". Next you will be asked which partition on the CD-ROM the distribution is to be loaded from. This is normally partition "a". Next you will have to identify the file system type that has been used to create the distribution on the CD-ROM, this can be either FFS or ISO CD9660. The OpenBSD CD-ROM distribution uses the CD9660 format. You will also have to provide the relative path to the directory on the CD-ROM which holds the distribution, for the luna88k this is "3.8/luna88k". For instructions on how to complete the installation from the CD-ROM distribution, see the section named "Common file system installations" below. To install from an NFS mounted directory: When installing from an NFS-mounted directory, you must have completed network configuration above, and also set up the exported file system on the NFS server in advance. First you must identify the IP address of the NFS server to load the distribution from, and the file system the server expects you to mount. The install program will also ask whether or not TCP should be used for transport (the default is UDP). Note that TCP only works with newer NFS servers. You will also have to provide the relative path to the directory on the file system where the distribution sets are located. Note that this path should not be prefixed with a '/'. For instructions on how to complete the installation from the CD-ROM distribution, see the section named "Common file system installations" below. To install from a local disk partition: When installing from a local disk partition, you will first have to identify which disk holds the distribution sets. This is normally "sdN", where N is a number 0 through 9. Next you will have to identify the partition within that disk that holds the distribution; this is a single letter between 'a' and 'p'. You will also have to identify the type of file system residing in the partition identified. Currently, you can only install from partitions that have been formatted as the Berkeley fast file system (ffs). You will also have to provide the relative path to the directory on the file system where the distribution sets are located. Note that this path should not be prefixed with a '/'. For instructions on how to complete the installation from a local disk partition, see the next section. Common file system installations: The following instructions are common to installations from mounted disk partitions, NFS mounted directories and CD-ROMs. A list of available distribution sets will be listed. You may individually select distribution sets to install or enter `all' to install all of the sets (which is what most users will want to do). You may also enter `list' to get a file list or `done' when you are done selecting distribution sets. You may also use wildcards in place of a file name, e.g. `*.tgz' or even `base*|comp*'. It is also possible to enter an arbitrary filename and have it treated as a file set. Once you have selected the file sets you want to install and entered `done' you will be prompted to verify that you really do want to extract file sets. Assuming you acquiesce, the files will begin to extract. If not, you will be given the option of installing sets via one of the other install methods. Common URL installations: Once you have entered the required information, the install program will fetch a file list and present a list of all the distribution sets that were found in the specified directory. (If no valid sets were found, you will be notified and given the option of unpacking any gzipped tar files found or getting a file list if none were found.) At this point you may individually select distribution sets to install or enter `all' to install all of the sets (which is what most users will want to do). You may also enter `list' to get a file list or `done' when you are done selecting distribution sets. You may also use wildcards in place of a file name, e.g. `*.tgz' or even `base*|comp*'. It is also possible to enter an arbitrary filename and have it treated as a file set. Once you have selected the file sets you want to install and entered `done' you will be prompted to verify that you really do want to download and install the files. Assuming you acquiesce, the files will begin to download and unpack. If not, you will be given the option of installing sets via one of the other install methods. When all the selected distribution sets has been extracted, you will be allowed to select which time zone your system will be using, all the device nodes needed by the installed system will be created for you, and the file systems will be unmounted. For this to work properly, it is expected that you have installed at least the "base38", "etc38", and "bsd" distribution sets. Congratulations, you have successfully installed OpenBSD 3.8. When you reboot into OpenBSD, you should log in as "root" at the login prompt. You should create yourself an account and protect it and the "root" account with good passwords. You should have got a mail from the install program we recommend you to read, it contains answers to basic questions you might have about OpenBSD (like setting up your system, installing packages, getting more information about OpenBSD, sending in your dmesg output and more). This you can do by running mail and then just enter "more 1" to get the first message. You quit mail by entering "q". Some of the files in the OpenBSD 3.8 distribution might need to be tailored for your site. We recommend you run: man afterboot which will tell you about a bunch of the files needing to be reviewed. If you are unfamiliar with UN*X-like system administration, it's recommended that you buy a book that discusses it. Upgrading a previously-installed OpenBSD System: ------------------------------------------------ Warning! Upgrades to OpenBSD 3.8 are currently only supported from the immediately previous release. The upgrade process will also work with older releases, but might not execute some migration tasks that would be necessary for a proper upgrade. The best solution, whenever possible, is to backup your data and reinstall from scratch. To upgrade OpenBSD 3.8 from a previous version, start with the general instructions in the section "Installing OpenBSD". Boot from an installation tape, or a bsd.rd file on the root file system. When prompted, select the (U)pgrade option rather than the (I)nstall option at the prompt in the install process. The upgrade script will ask you for the existing root partition, and will use the existing filesystems defined in /etc/fstab to install the new system in. It will also use your existing network parameters. From then, the upgrade procedure is very close to the installation procedure described earlier in this document. Note that the upgrade procedure will not let you pick the ``etc38.tgz'' set, so as to preserve your files in `/etc' which you are likely to have customized since a previous installation. However, it is strongly advised that you unpack the etc38.tgz set in a temporary directory and merge changes by hand, since all components of your system may not function correctly until your files in `/etc' are updated. Getting source code for your OpenBSD System: -------------------------------------------- Now that your OpenBSD system is up and running, you probably want to get access to source code so that you can recompile pieces of the system. A few methods are provided. If you have an OpenBSD CD-ROM, the source code is provided. Otherwise, you can get the pieces over the Internet using anonymous CVS, CTM, CVSync or FTP. For more information, see http://www.OpenBSD.org/anoncvs.html http://www.OpenBSD.org/ctm.html http://www.OpenBSD.org/cvsync.html http://www.OpenBSD.org/ftp.html Using online OpenBSD documentation: ----------------------------------- Documentation is available if you first install the manual pages distribution set. Traditionally, the UN*X "man pages" (documentation) are denoted by 'name(section)'. Some examples of this are intro(1), man(1), apropos(1), passwd(1), passwd(5) and afterboot(8). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The 'man' command is used to view the documentation on a topic, and is started by entering 'man [section] topic'. The brackets [] around the section should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the least-numbered section name will be displayed. For instance, after logging in, enter man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter man 5 passwd instead. If you are unsure of what man page you are looking for, enter apropos subject-word where "subject-word" is your topic of interest; a list of possibly related man pages will be displayed. Adding third party software; ``packages'' and ``ports'': -------------------------------------------------------- As complete as your OpenBSD system is, you may want to add any of several excellent third party software applications. There are several ways to do this. You can: 1) Obtain the source code and build the application based upon whatever installation procedures are provided with the application. 2) Use the OpenBSD ``ports'' collection to automatically get any needed source file, apply any required patches, create the application, and install it for you. 3) Use the OpenBSD ``package'' collection to grab a pre-compiled and tested version of the application for your hardware. If you purchased the OpenBSD CD-ROM set you already have several popular ``packages'', and the ``ports'' collection. Instructions for installing applications from the various sources using the different installation methods follow. You should also refer to the packages(7) manual page. Installing applications from the CD-ROM package collection: The OpenBSD CD-ROM ships with several applications pre-built for various hardware architectures. The number of applications vary according to available disk space. Check the directory 3.8/packages/m88k to see which packages are available for your hardware architecture. That directory will be on the same CD-ROM containing the OS installation files for your architecture. To install one or more of these packages you must: 1) become the superuser (root). 2) mount the appropriate CD-ROM. 3) use the ``pkg_add'' command to install the software. Example (in which we use su(1) to get superuser privileges, thus you have to be in group "wheel", see the manual page for su(1)). $ su Password: # mkdir -p /cdrom # mount /dev/cd0a /cdrom # pkg_add /cdrom/3.8/packages/m88k/ # # umount /cdrom Package names are usually the application name and version with .tgz appended, e.g. emacs-21.3.tgz Installing applications from the ftp.OpenBSD.org package collection: All available packages for your architecture have been placed on ftp.OpenBSD.org in the directory pub/OpenBSD/3.8/packages/m88k/ You may want to peruse this to see what packages are available. The packages are also on the OpenBSD FTP mirror sites. See http://www.OpenBSD.org/ftp.html for a list of current FTP mirror sites. Installation of a package is very easy. 1) become the superuser (root) 2) use the ``pkg_add'' command to install the software ``pkg_add'' is smart enough to know how to download the software from the OpenBSD FTP server. Example: $ su Password: # pkg_add \ ftp://ftp.OpenBSD.org/pub/OpenBSD/3.8/packages/m88k/emacs-21.3.tgz Installing applications from the CD-ROM ports collection: The CD-ROM ``ports'' collection is a set of Makefiles, patches, and other files used to control the building and installation of an application from source files. Creating an application from sources can require a lot of disk space, sometimes 50 megabytes or more. The first step is to determine which of your disks has enough room. Once you've made this determination, read the file PORTS located on the CD-ROM which contains the ports tree. To build an application you must: 1) become the superuser (root) 2) have network access, or obtain the actual source files by some other means. 3) cd to the ports directory containing the port you wish to build. To build samba, for example, where you'd previously copied the ports files into the /usr/ports directory: cd /usr/ports/net/samba 4) make 5) make install 6) make clean Installing applications from the OpenBSD ports collection: See http://www.OpenBSD.org/ports.html for current instructions on obtaining and installing OpenBSD ports. You should also refer to the ports(7) manual page. Installing other applications: If an OpenBSD package or port does not exist for an application you're pretty much on your own. The first thing to do is ask if anyone is working on a port -- there may be one in progress. If you can't find an existing port, try to make your own and feed it back to OpenBSD. That's how our ports collection grows. Some details can be found at http://www.OpenBSD.org/porting.html with more help coming from the mailing list, . Administrivia: -------------- There are various mailing lists available via the mailing list server at . To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instructions. There are also two OpenBSD Usenet newsgroups, comp.unix.bsd.openbsd.announce for important announcements and comp.unix.bsd.openbsd.misc for general OpenBSD discussion. To report bugs, use the 'sendbug' command shipped with OpenBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: bugs@OpenBSD.org Use of 'sendbug' is encouraged, however, because bugs reported with it are entered into the OpenBSD bugs database, and thus can't slip through the cracks. As a favor, please avoid mailing huge documents or files to the mailing lists. Instead, put the material you would have sent up for FTP somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. For more information about reporting bugs, see http://www.OpenBSD.org/report.html